Tennis Court Resurfacing Guidelines: 10 Best Practices for Applying Tennis Court Surfaces

1. Longevity and performance of color coating systems are dependent on proper construction of the court. Consult the ASBA (American Sports Builders Association) website for detailed guidelines.

Proper slope requirements are.8333% – 1.0%

Adequate surface and subsurface drainage should be installed to prevent water accumulation beneath the surface.

Concrete courts should have a vapor barrier installed House Construction Services beneath the slab (10 mil thickness recommended).

Concrete Courts should be finished with a medium-broom texture, and no curing compounds should be used.

Consult the coating manufacturer’s specifications and guidelines for full concrete preparation instructions.

2. Make sure that new asphalt or concrete is fully cured

28 days for concrete

30 days recommended for asphalt (during prime curing conditions of moderate sun to draw out oils and rain to rinse away.

Make sure that the existing surface is not coated with a pavement sealer. Building Contractor Meaning In Tamil Acrylics do not bond well to coal tar or most asphalt-based sealants.

3. Surface Repair

1 Hour after a rain or flooding the court, outline any puddle areas with chalk that cover a 5-cent piece (American coin). These areas should be repaired with Acrylic Patch Binder patching mix.

Fill all cracks over 1/8″ wide with a suitable acrylic-based crack sealant. Never use a hot or cold applied asphalt-based crack filler.

4. Clean the court surface prior to application of repair products or coatings. Any areas where mold, mildew, or fungus is evident should be treated with a solution of 2 parts water to 1 part household bleach. Spray and broom in the bleach solution and allow it to sit for 20 to 30 minutes. Scrub with brooms or suitable equipment, then rinse thoroughly with a pressure washer. It’s a good idea to treat any areas exposed to shade with this method.

5. Always follow the manufacturer’s mixing instructions. Never over-dilute the coatings in order to “stretch” coverage. The specified sand size and shape are very important to the look and performance (speed of play) of the surface. If the proper sand types are not available in your area, purchase the coatings directly from the manufacturer with sand pre-added.

6. Follow the manufacturer’s application and curing temperatures

Apply products when temperatures are 50 degrees and rising

The best time to apply is in the morning when the surface is cooler. If application during hot temperatures is unavoidable, the surface can be lightly misted to cool the pavement. Do not puddle. Use a garden pump sprayer or a hose nozzle with mist setting.

Acrylic Resurfacer and Color Coatings normally dry within 1 hour of application in the full sun (based on 75 day with low humidity). Shade, low temperatures, and high humidity can increase drying times.

7. Use the proper tools and equipment for mixing and application:

Floor Scrapers: Use to scrape foreign objects off of the surface prior to application, and gently scrape the surface between coats to remove small bumps and imperfections. Do not scrape the finish coat.

Grass Trimmers: Trim around …

Australian Construction Industry Requirements, Laws and Guidelines – How Do They Apply To You?

Not happy with your recent renovations? Blame the contractor. Sure, you can do that – many people do and sometimes its justified but what if you’d rather avoid that situation altogether? If you want to ensure that your new deck, shed or patio looks fantastic, there are definitely some things that you can do.

A carpenter is paid for their physical skill but also for their knowledge. A qualified carpenter is aware of the laws and regulations regarding renovations and construction. For this reason, people hiring carpenters often feel that there is no particular reason for them to be familiar with any of the laws or regulations relevant to their project.

If you have done your research, then chances are you have contracted the services of a good carpenter, however, there is never any guarantee and if you have hired a random contractor or a “handyman” your risk level may be higher.

Even if you believe that you can trust your carpenter, you should always protect yourself regardless. The Council of Australian Governments (COAG) developed the National What Is A Qualified Builder Code (NCC) to incorporate all on-site construction requirements into a single code. You can check the guidelines for your specific renovation or building plans for yourself.

A hardcopy version of the NCC is available at various outlets throughout Australia for viewing. You can check out the locations near you on the ABCB website. You can also view the National Construction Code 2012 by purchasing a 12 Day (for occasional) or 30 Day Monthly (for short-term) web access for under $100 (Prices checked 19th January 2012.) See the end of the article for links.

Another set of guidelines that it is good to be familiar with is the Local Environmental Plan (LEP) in your council area. Depending on the size of your project, your carpenter may have been required to lodge a Development Application (DA). Prior to submitting an application, you should contact your local council to obtain any relevant Development Control Plans (DCP) or guidelines and familiarize yourself with them.

If you see work being undertaken that appears to be in breach of any of these guidelines, you can address the issue before the project goes any further. Show a copy of the NCC, LEP, DA or DCP requirements to your carpenter and tell them you are concerned that the work being done might not meet them.

If you aren’t satisfied with the response you get, phone your local council or the Building Services Authority (BSA) on 1300 272 272 and ask them to do an assessment of the work being carried out.

The BSA is a fantastic organization that actually offers Smart Building and Renovating Presentations. For more information you can call them, or check the link for their website at the end of the article. You can also contact them to find out whether there are any other laws or guidelines not mentioned in this article that you need to be aware of in your State …

Six Guidelines for Choosing a Bathroom Contractor

When doing some bathroom remodeling, you may find that your DIY skills are not up to the remodeling job yourself. While it can be fun to remodel your bathroom and do all the work yourself, it is usually a better choice to hire a contractor to get the job done. Not only will it end up being done much quicker, but you will be able to invest your time doing the things you need and want to do rather than spending it all doing the remodel.
Hiring the right contractor to remodel your bathroom is important, so here are six guidelines to follow when looking for a bathroom remodeling contractor:
Chat with Friends
If you want to find the best contractor to remodel your bathroom, it is important that you find a good one that you can trust. Find out if any of your friends or family members know of a contractor that will do a good job, or one that has done good work for them in the past. This referral from someone you trust is usually the best way to find a quality bathroom remodeling contractor.
Check References Building Contractor Meaning In Tamil
Once you have gotten in contact with the contractor and spent time talking with him about the job, ask for references you can call. Checking them out by calling references is important, as that is the best way to know if they are worth it. The people you call will always be happy to tell you if the job was good or not, and they will be honest with you about the service’s pros and cons.
Ensure they are Certified
The certifications obtained by a contractor say a lot about their professionalism, so always check what certifications they have. Obviously there is nothing to replace years of experience, but certification with the BBB and the local contractor organizations will help you to know if the business is above-board or not.
Always Draw Up a Contract
Before you start doing the job, make sure that you have a written contract that spells everything out in detail. A gentlemen’s agreement may be great, but what do you do if the contractor tries to back out of a job? With a contract, you can be protected from the contractor trying to get out of doing certain work, and the contractor will be protected if you try to flake on the payment.
The Job Must Be Construction Services Definition Done Punctually
The job always should be done punctually or within the time frame that the contractor specified. Sure there are going to be setbacks or problems that could cause the job to take longer, but the good contractors always come through and finish when they tell you they will.
Never Pay Cash
If the contractor asks you to pay cash, it may be a sign that they aren’t as honest or reputable as you might want. The honest contractors will usually request a bank deposit or a check, as …

Guidelines For Job Hunters

Searching for the perfect job is always a difficult task. One has to browse through the listings available in newspapers, websites, and other places such as employment exchanges very carefully to find a career that match one’s profile. There is a range of online services that cater to needs of the burgeoning career market. It is necessary to find the service which is right for you. This itself, would take some time as different online services list different kinds of vacancies for prospective employees. The trick is to keep a track of postings on these websites and apply as soon as a suitable vacancy is found.
How to search through the variety List Of General Contractors of occupation categories
There are a plethora of employment opportunities in the career market for the different qualifications and educational backgrounds that people have. They have to choose the sector according to their educational background. A person who has a degree in mass communication should be looking for a career in the media or advertising industry. Since careers in these fields require advanced communication skills, the sector would be suitable for a mass communication graduate. Likewise, people who have degrees in social work will find ample opportunities in the different non-governmental organizations (NGOs).
Things one should keep in mind
It is really the aptitude of a person that decides the kind of job he or she is suitable for. A person should also keep his interests and inclinations in mind while looking for means of earning a living. Past work experience helps a person to narrow down on the job vacancy options and zero in on the suitable vacancy. People usually gain a strong foothold in a particular industry after a number of years of experience. In these cases, recruiters would be keen to hire such people on grounds of their experience and their significant contributions in the particular sector.
Recruiters are interested in hiring people who demonstrate strong skills relating to team work and communication. For fresh graduates who do not have a working experience, past volunteering activities come handy. It is imperative for such people to mention their extra-curricular activities while applying for a job.
People may not always be successful in finding their dream job. But this should egg them on to find other possibilities that would be suitable to their profile. Small House Plans Pdf By acquiring experience, one can find the desired career after one has gathered experience in related fields. Till then, it’s happy job hunting everyone!…

Safety Precautions and Guidelines in the Construction Industry

Safety is a priority. This is an age old adage always emphasized in construction given the gravity and repercussions of a minute lapse in judgement when working in the field. The health and safety of construction personnel and civilians is the #1 priority and is essential to the successful completion of the project.
Since most accidents can be prevented, construction personnel should be more proactive and aware of the work hazards by employing basic common sense and discretion in collaboration with knowledge of these hazards and work- related policies on safety. Here are some of the common safety and health hazards in Concrete Construction:
• When handling fresh concrete, wear protective gear like long- sleeved shirts, rubber boots, gloves and protective eyewear. This is because fresh concrete can cause burns and eye injuries upon contact. If one comes in contact with fresh concrete, rinse it off with running water from a faucet.
• Finishers should remove clothing that has been soaked with fresh concrete, they should also wear protective clothing in the form of work boots, knee pads, long pants, gloves, and if available, knee boards.
• Remember the PPEs (Personal Protection Equipment): Gloves, hard hats, gloves, boots, eye protection, and additional miscellaneous weather protection clothing. These keep the worker safe from the short and long term hazards of working on-site
• When working in a noisy environment, ear plugs should be utilized. One will know the need for the ear plugs when the level of noise gets to a point where one worker has to raise their voice to another employee working beside them.
• Workers should wear respirators or dust masks if the work requires them to be exposed to dirt, mist, ships, or dust like when they are cutting, mixing grout, or chipping solidified concrete since it may irritate the respiratory system Home Remodeling Before And After and cause disease. Using dustless vacuum equipment and “wet” methods can also be used as an alternative, and to guarantee the correct selection and use of a respirator, trainings and seminars should be should be held for the employees.
• Construction job employers should educate and thoroughly train construction employees on fall hazards since it is one of the main causes of injuries and deaths among construction workers. The contents of the training should include the right procedures for establishing, maintaining, and removing fall protection systems, the proper use, handling, care, and maximum weight capacity of load carrying ladders.
• When using scaffolding, even for a short period of time, it should be sturdily built. Competent personnel should assess the construction of the scaffolding every day, checking that the scaffolding is upright, with a good foundation, and uniformly spaced. Employing horizontal or diagonal bracing, tying the scaffold to a solid structure like a building or a wall, and planking that overlaps support by a good 12 inches are guidelines to ensure its stability.
• The risk for falls is higher when the construction worker moves from place to place while …